microwave corporation 12 - 26 for price, delivery, and to place orders, please contact hittite microwave corporation: 12 elizabeth drive, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order online at www.hittite.com mixers - smt 12 HMC171C8 gaas mmic smt double- balanced mixer, 7 - 10 ghz v01.0801 general description features functional diagram conversion loss: 9.0 db lo to rf isolation: 32 db surface mount small size, no dc bias required electrical speci cations, t a = +25?c, lo drive = +10 dbm typical applications the HMC171C8 is ideal for: microwave pt to pt radios 5.8 ghz ism band circuits the HMC171C8 is a miniature double-balanced mixer in a non-hermetic ceramic surface mount package that can be used as an upconverter, downconverter or biphase modulator. the device is a passive diode/balun type mixer with high dynamic range. noise ? gure is essentially equal to the conversion loss. the mixer can handle larger signal levels than most active mixers due to the high third order intercept. mmic imple- mentation provides exceptional balance in the cir- cuit resulting in high lo/rf and lo/if isolations and unit-to-unit consistency. this mixer has appli- cations in circuits where small size and surface mount compatibility are important. parameter min. typ. max. units frequency range, rf & lo 7.0 - 10.0 ghz frequency range, if dc - 2 ghz conversion loss 910 db noise figure (ssb) 910 db lo to rf isolation 28 32 db lo to if isolation 21 26 db ip3 (input) 12 16 dbm ip2 (input) 55 62 dbm 1 db gain compression (input) 7 10 dbm
microwave corporation 12 - 27 for price, delivery, and to place orders, please contact hittite microwave corporation: 12 elizabeth drive, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order online at www.hittite.com mixers - smt 12 -20 -15 -10 -5 0 conversion loss (db) 0123456789101112 frequency (ghz) -60 -50 -40 -30 -20 -10 0 0123456789101112 isolation (db) frequency (ghz) rf/if lo /if lo/rf lo/if conversion loss isolation -15 -12.5 -10 -7.5 -5 conversion loss (db) 2345678 91011121314 frequency (ghz) +15dbm +13dbm +10dbm +9dbm +8dbm conversion loss vs lo drive v01.0801 HMC171C8 gaas mmic smt double- balanced mixer, 7 - 10 ghz -40 -30 -20 -10 0 return loss (db) 0123456789101112 frequency (ghz) if rf lo return loss distortion and 1db compression vs. lo drive level s - paremeters for the rf, lo, if ports are available on-line at www.hittite.com distortion lo drive rf (f1) = 8.01 ghz rf (f2) = 8.00 ghz lo = 8.5 ghz rf level = 0 dbm 1 db compression (dbm) ip3 (dbm) ip2 (dbm) p1db (dbm) +7 13 59 8.5 +10 16 62 10.0
microwave corporation 12 - 28 for price, delivery, and to place orders, please contact hittite microwave corporation: 12 elizabeth drive, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order online at www.hittite.com mixers - smt 12 outline drawing absolute maximum ratings v01.0801 HMC171C8 gaas mmic smt double- balanced mixer, 7 - 10 ghz rf / if input +13 dbm lo drive +27 dbm storage temperature -65 to +150 c operating temperature -55 to +85 c notes: 1. package body material: white alumina 92% 2. lead, package bottom material: copper 3. plating: electrolytic gold 100-200 microinches, over electrolytic nickel 100-250 microinches. 4. dimensions are in inches [millimeters]. 5. package length and width dimensions do not include lid seal protrusion .005 per side. 6. all ground leads and ground paddle must be soldered to pcb rf ground.
microwave corporation 12 - 29 for price, delivery, and to place orders, please contact hittite microwave corporation: 12 elizabeth drive, chelmsford, ma 01824 phone: 978-250-3343 fax: 978-250-3373 order online at www.hittite.com mixers - smt 12 v01.0801 HMC171C8 gaas mmic smt double- balanced mixer, 7 - 10 ghz evaluation pcb list of material item description j1 - j3 pc mount sma rf connector u1 HMC171C8 mixer pcb* 107214 evaluation board * circuit board material: rogers 4350 the circuit board used in the ? nal application should use rf circuit design techniques. signal lines should have 50 ohm impedance while the package ground leads and exposed paddle should be connected directly to the ground plane similar to that shown. a suf? cient number of via holes should be used to con- nect the top and bottom ground planes. the evalua- tion circuit board shown is available from hittite upon request.
|
